How-To Videos

How to Patch a Hole in an Asphalt Driveway

By: Allen Lyle

Asphalt driveways can become damaged over time from erosion, tree roots, or heavy loads. To fix a hole in an asphalt driveway:

  1. Use a circular saw with an abrasive masonry blade to cut around the hole to provide a clean edge.
  2. Remove the asphalt and any loose soil from the damaged area with a shovel.
  3. For edge repairs, install a board even with the edge to hold the asphalt in place while it sets.
  4. Pour crushed limestone or gravel into the hole to act as a base for the asphalt.
  5. Tamp down base material using a hand tamp.
  6. Fill the hole with an asphalt repair material, like Blacktop Repair from Quikrete.
  7. Tamp down the asphalt repair material.
  8. Cover the patch with plywood, and drive over it to compact the patch.

Watch this video to find out more.

Further Information

Video Transcript

Now, this problem may not affect everybody, but if you’ve got an asphalt driveway, chances are you’ll be faced with this sooner or later, and I’m talking about a pothole. It might be in the center; or, as we have here, a divot that was out on the side.

It’s pretty easy to repair. First of all, we’re going to remove all of the loose debris, get it out of the way, clear it out. And in this case, as I was doing it, I found out that we had a rather massive root right in the middle of it, so we had to get the root out as well. Once that’s out of the way, we’re going to dig out that area.

We want to square off the edges. In the center of a driveway, cut a square. Here I just did somewhat of a triangle, just to give me some good edges to go to. Now, because it’s on the edge, I’ve also put in an edge board to keep it in place.

From that point I was ready for my base, and this is important, folks. Make sure you’re not putting this right on top of the dirt, cause it will settle. Put a nice base of crushed limestone; or, as we did here, gravel.

And now I’m ready for my blacktop repair. Pour it in, it’s going to be messy, wear some old clothes. Spread it out, get a steel rake, tamp it down. It looks nice now, but we’re not quite through with it. What I’m going to do next is put a piece of plywood on top and drive a car right on top of it, to help pack it in.


Please Leave a Comment

3 Comments on “How to Patch a Hole in an Asphalt Driveway”

You can follow comments to this article by subscribing to the RSS news feed with your favorite feed reader.

  • John Hurt Says:
    August 18th, 2019 at 4:05 pm

    Would like to see a video showing how to fix a hole in my driveway as a result of a wet spot underneath the driveway.

  • Carla Sikinger Says:
    May 16th, 2019 at 11:22 am

    Loved this video, thank you. It’s easier to do a hole like that when it’s flat but my driveway has the same hole, on the edge with just dirt underneath but it’s on an incline. Will the asphalt start to move away from upper edge as it dries? Would like to see a video of fixing a hole on a steep driveway.

  • Benito Mendez Says:
    May 31st, 2016 at 6:56 pm

    Very helpful video, we had an incident on our job site , we did a couple of holes with a machine wheels and we was responsible to fixing it, I look on the web and this is the most easiest way, we almost hire somebody to do it, at the end we did it and looks like nothing happened, thank you for everything.

We want to hear from you! In addition to posting comments on articles and videos, you can also send your comments and questions to us on our contact page or at (800) 946-4420. While we can't answer them all, we may use your question on our Today's Homeowner radio or TV show, or online at

 characters available

How to Patch a Hole in an Asphalt Driveway